![]() ![]() ![]() After completing the template, put it on the perf board, which serves as the custom PCB. ![]() Mark the top and bottom, so they fit perfectly in the required space. Position it so that it stays far enough from the tail light lens. ![]() Then, pry the lens out gently.Ĭreate a cardboard template of the tail light. Turn on the oven to 100☏ and place the taillight inside for seven minutes to soften the sealant. Pull apart OE BMW wires diy led tail light steps Step One:įirst, gently take out the taillights covering with a Phillips head screwdriver.022″ Silver bearing rosin core solder – 1x 220 Ohm 1/4 watt resistors with 5% tolerance – 9x.Red 5mm Superflux LEDs (strong light output) – 36x.Philips head screwdrivers Components needed:.So let’s get started! DIY led tail light: how to make led tail light. How to make led tail light, This guide will put you on the right path toward that ultimate experience. On the other hand, building one provides many advantages and saves you money in the long run. While it may seem like a more straightforward solution to buy them, it’s also quite expensive. If that ever happens, we face two options to replace them, purchasing new ones or building LED tail lights. However, we may come across a problem: start-up failure. 2018-2023 Harley-Davidson® Low Rider (FXLR) and Low Rider S (FXLRS) require Low Rider Integrated Taillight Adapter Harness for proper operation (sold separately).Vehicle tail lamps commonly serve as a safety net for other drivers. Note: Additional wiring adapter required on 2022-2023 Low Rider ST (FXLRST) & 2022 Low Rider El Diablo (FXRST). Replacement gasket and nylon washers included for easy plug and play installation into OEM taillight circuit board for 1999-2013 Harley-Davidson® Sportster models (Except XL1200N, XL1200X, XL1200V or XL883N) 2014-2022 XL883L & XL1200T, 1999-2017 Dyna models (Except 2009-2017 FXDB, 2010-2017 FXDWG), 1999-2017 Softail models (Except FXS, FLS, FXSB, FXSBSE, FXSTD, FXSTDSE, FLSTN, FLSTNSE, FXCWC, 2010 FLSTSE2), 2018-2022 Heritage Classic (FLHC), Low Rider (FXLR), Low Rider S (FXLRS), 1999-2013 Electra Glide, Ultra Classic, Ultra Limited models (including CVO™), Road King Classic (FLHRC), Road Glide Ultra (FLTRU), Road Glide Ultra CVO™ (FLTRUSE), 1999-2009 Road Glide Standard (FLTR), 2006-2009 Street Glide (FLHX), 1999-2022 Road King (FLHR),2014-2015 Limited CVO™, 2015 Road Glide Ultra CVO™ (FLTRUSE), 2022 Street Glide ST (FLHXST), 2022 Road Glide ST (FLTRXST) and 2019-2022 Electra Glide Standard (FLHT) Replacement for OEM Part 68245-03.Ĭompatible with 1999-Earlier Harley-Davidson Motorcycles when installed with a Taillight Baseplate Replacement for 1999-Earlier Harley-Davidson® motorcycles (sold separately) and Integrated Taillight Wire Harness (sold separately).ġ999-2013 Harley-Davidson® Sportster models (Except XL1200N, XL1200X, XL1200V or XL883N) 2014-2022 XL883L & XL1200T, 1999-2017 Dyna models (Except 2009-2017 FXDB, 2010-2017 FXDWG), 1999-2017 Softail models (Except FXS, FLS, FXSB, FXSBSE, FXSTD, FXSTDSE, FLSTN, FLSTNSE, FXCWC, 2010 FLSTSE2), 2018-2023 Heritage Classic (FLHC), Low Rider (FXLR), Low Rider S (FXLRS), 2022-2023 Low Rider ST (FXLRST), 2022 Low Rider El Diablo (FXRST), 1999-2013 Electra Glide, Ultra Classic, Ultra Limited models (including CVO™), Road King Classic (FLHRC), Road Glide Ultra (FLTRU), Road Glide Ultra CVO™ (FLTRUSE), 1999-2009 Road Glide Standard (FLTR), 2006-2009 Street Glide (FLHX), 1999-2022 Road King (FLHR), 2014-2015 Limited CVO™, 2015 Road Glide Ultra CVO™ (FLTRUSE), 2022-2023 Street Glide ST (FLHXST) & Road Glide ST (FLTRXST) and 2019-2022 Electra Glide Standard (FLHT). The low profile design protrudes only two inches from the stock taillight baseplate for a sleek, custom, all-in-one solution for the rear fender. ProBEAM ® Integrated taillight combines 5 LED running light pipes with full contrast red brake LEDs with built in left and right amber auxiliary turn signals. ![]()
0 Comments
Leave a Reply. |